Our cerium oxide particles are very durable and do not wear out as quickly as competitors' products. Their uniform particle size distribution means high glass removal efficiency.
Our cerium oxide does not clump after a long period of standing, and can quickly suspend from the bottom when the machine runs again, ensuring extremely high utilization efficiency. Cerium oxide does not adhere to machine/pipe or glass surfaces. Due to its built-in suspension dispersant, it can be easily cleaned.
Cerium oxide is a high-quality polishing compound used to remove small scratches, "dead spots," and wear marks on glass and mirrors. Scratched glass, mirrors, and even car headlights can be quickly and easily repaired by coating the glass surface with cerium oxide slurry and carefully polishing it with a felt polishing wheel. In addition, it is commonly used for straight glass edge grinding and flat glass chamfering, as well as manual and machine polishing. High quality cerium oxide will not adhere to machine/pipe or glass surfaces. Optimization formula for flat glass edge grinding and mirror inclined surface. Our products have excellent suspension quality, are resistant to hardening, and are easy to clean.
The following is the usage requirements for polishing processing, for your reference
1. The ratio of polishing solution
Determination and adjustment of polishing solution concentration
1). The solubility of polishing solution is usually controlled between 1.03 and 1.05 in density. The new polishing solution is formulated with 100 grams of cerium oxide polishing powder per kilogram of pure water (ratio: 1:10) as the standard (note: depending on different production needs and the properties of the polishing powder material, different companies also adjust the ratio of pure water to polishing powder to 1:7). If the density of the old polishing solution is ≤ 1.03, polishing powder needs to be added, and if it is ＞ 1.05, water should be added to dilute it.
Note: When preparing polishing solution, due to the agglomeration of some brands of polishing powder, it is recommended to add an appropriate amount of RO hot water for mixing and manually stir. Then use a filter to filter into the polishing machine mixing bucket, stir thoroughly for 5 minutes and circulate for more than 2 minutes to ensure the full fusion of polishing powder and RO water.
2). When the pH value of the polishing solution is usually controlled at around 7.5, the polishing efficiency of the polishing solution can reach a better state. If the pH is too low and slightly acidic, you can add some sodium hydroxide to neutralize it. Conversely, if the pH is too high and slightly alkaline, you can add some citric acid or glacial acetic acid to adjust the pH range.
2. Monitoring time and replacement cycle of concentration and pH value in the use of polishing solution
1) In actual polishing operations, it is recommended to check the concentration and pH value of the polishing solution every 4 hours, and add polishing powder 1-2 times per shift or according to the actual situation.
2) It is recommended to replace the polishing solution in the container of the polishing machine every 30 days
3) When the specific gravity of the polishing solution is between 4-8%, it is found that the concentration of the polishing solution decreases during the monitoring process. The simple calculation reference formula for the amount of polishing powder added is as follows: the amount added per liter=(12% - current specific gravity) kg/L.
3. First Aid
Eyes: Flush eyes with lukewarm water, including under upper and lower eyelids, for at least 15 minutes.
Skin: Remove contaminated clothing, a brush material off skin wash affected area with soap and water.
Ingestion: Rinse mouth with water. Do not induce vomiting. Seek medical attention. Never induce vomiting or give anything by mouth to an unconscious person.
FAQ
Q: Who are you?
A: We are a manufacturer from China specializing in the production of glass polishing powder, particularly skilled in manufacturing polishing powder for glass edge grinding
Q: What polishing powder do you have?
A: We have three types of polishing powders: DL-XP (blue font), DL-XP (red font), and XP-CF. They are used for glass edge polishing, glass scratch removal and repair, glass thinning, and cleaning. They can also be OEM.
Q: What is your payment terms ?
A: FOB or EXW price is our usual price term . Payment<=1000USD,100%in advance.Payment>=1000USD,30%T/T in advance, balance before shipment. If you need CIF price, please let us know your port of destination.
Q: How can we guarantee quality?
A: We regard the quality of products as life, our products through layers of checks, we strictly control the testing of products,products are confirmed to be qualified before delivery and installation.
Q: How could I get a sample?
A: Before we received the first order, please afford the sample cost and express fee. We will return the sample cost back to you within your first order.
Hot Tags: glass edge polishing powder, China glass edge polishing powder manufacturers, suppliers, factory, economy glass polishing powder, Durable Glass Polishing Powder, glass polishing powder for new glass, glass polishing powder for glass sculptures, glass polishing powder for shined glass, efficient glass polishing powder